How To Load A Grease Gun Without A Cartridge

How To Load A Grease Gun Without A Cartridge : One of the most common household tools is the grease gun. You’ll find one in almost any garage or manufacturing facility. Our stores rely heavily on it without much thought. It’s one of those tools we use every day. Here is a guide on how to prevent a grease gun from jamming without a cartridge.

Grease guns are efficient means of transferring grease to the application level, although they are often overlooked. Grease and lubricants are commonly applied to moving parts and mechanical surfaces with this machine. Lubricating oil is pumped under pressure to bearing areas normally inaccessible without disassembly to deliver lubrication.

Lubricating guns can be defined as being either air-powered, battery-powered, handgrip, hand grip, or lever type. Most people use the lever type grease gun since it’s so inexpensive and widely available.

They are used in a diverse range of DIY and industrial environments, with common examples including:

Loading a grease gun without a cartridge

Loading grease guns without cartridges is somewhat challenging, but it’s relatively straightforward if you follow the right instructions and have a clear understanding of how the guns work. If you know all the stuff about how to load a grease gun, it becomes a piece of cake, and you won’t have problems maintaining your setup.

Following these steps will allow you to load your grease gun without a cartridge. This requires a large container full of bulk grease.

Step — 2

In the next step, you fill the barrel by gently pulling the plunger rod back while drawing grease into the barrel while holding it down at the distal end of the barrel inside the grease holder. Local hardware retail stores may also carry large grease containers, which are useful for professionals.

Step — 3

There will be some differences in the grease gun as you run it. To fix this, you might have to screw on the end cap or screw the nozzle back on. Therefore, it is mainly determined by the kind of grease gun you use.

Step — 4

The last step in the process is to test it with each component loaded and reassembled to see how it works. When you press the handle of the piston rod, you should see grease coming out of the applicator tube. Clean the excess grease from the gun with a pristine cloth or rag.

Step — 5

So you need to undo the cap on your grease gun head so you can separate it from the barrel. Connected to the head part are the handle and applicator tube. In order to separate the grease gun pieces from each other, loosen the double pieces. To ensure the piston rod is fully inserted in the barrel, make sure it is completely depilated. During the process, this unexpectedly avoids the possibility of sucking grease into the gun.

The plunger must be pulled back and locked into place by tilting it to the metal tab. To begin with, unscrew the cylinder one turn for easy access. As soon as you have undone the cylinder, detach and dispose of the old grease cartridge. Install the new cartridge by first removing the plastic cap, and then by sliding the open end in the cylinder. Peel away the metal cap and slide the cartridge into place. Reattach it to the cylinder and tighten it up, then loosen it a little so it functions just like moving the plunger back into place.

The top must first be untwisted, then the plunger must be pulled until it locks, making the bar visible. So you’re going to take your grease and remove the top cap and insert it into the tube, and then it is just a matter of screwing the cap back on and twisting it until it is tight, and then you unlock the plunger and you’re done.

While – and essentially – the plunger at the bottom is simply meant for inspecting the grease remaining. In this case, push the plunger in so that it is encased in grease while fully plugged up. Pull it until the grease is expelled. In turn, you will be able to see how much grease is left in the cartridge because grease is exposed on the raw material.

See also  How To Attach Grease Gun To Zerk Fitting

As a result, if you take the same distance from the middle of the cartridge, there will still be some grease inside, which shows the amount of grease inside the cartridge.

Leave a Comment